Whether I've owned or rented. Country cottage, or city condo. The last one was a 2 stage G.E. undersink model which lasted about 9 years, until the filters started to get bad manufacture reviews. It's hard to find filter systems that are super quality, pro size, like the APEC WFS-1000 without going reverse osmosis. This system is the same size as a whole house filter, but made for undersink drinking water!
The water from this unit is pretty much tasteless to me, which is ideal since tap water tastes awful. I grew up with Culligan, which has a certain taste to me, versus this which is just pure. Haven't tested it but plan to. We also added a line to the fridge ice maker so our ice is purified. It was easy to install in our home, and we've used it three months with no issues. The cables are long. today when our sink clogged and we had to drain it, got a mess over all the filters, and they water tubes were all long enough to put the whole unit (still assembled and attached), into the sink to rinse it off. I'm glad it's made in the USA so I know all the parts have stringent manufacturing guidelines. The only thing I would change, is ordering directly from apec instead ... full review
Plumbosolvency reduction: In areas with naturally acidic waters of low conductivity (i.e. surface rainfall in upland mountains of igneous rocks), the water may be capable of dissolving lead from any lead pipes that it is carried in. The addition of small quantities of phosphate ion and increasing the pH slightly both assist in greatly reducing plumbo-solvency by creating insoluble lead salts on the inner surfaces of the pipes.

The pore size of the filter, usually measured in microns, will determine what will be filtered through. While a standard micron size of 0.2 is small enough to block heavy metals such as lead and copper and large parasites such as Cryptosporidium, it will not block viruses. The National Sanitation Foundation sets a standard for effective water filtration products so look for an NSF stamp when selecting a filter to purchase.
There are multiple built in filters water bottles choices. Vestergaard's Lifestraw Go and Sawyers Personal Water Bottle are two examples. The Lifestraw Go filters specs say it will filter up to 1,000 liters (264 gallons) of water down to particulate matter larger than 0.2 microns Source Sawyer's Personal Water bottle absolute hollow fiber membrane inline filter down to 0.1 micron. Source
Advantage is that you are not adding any chemicals to your water, which takes out the guess work as far as dosage. The disadvantage, if it can even be called that, is that you have to have a source of heat(fire, stove, etc.) in order to bring the water to the boiling point. Also we have to remember that this does not remove chemical such as petroleum or pesticides which can be harmful as well.
The first continuous use of chlorine in the United States for disinfection took place in 1908 at Boonton Reservoir (on the Rockaway River), which served as the supply for Jersey City, New Jersey.[46] Chlorination was achieved by controlled additions of dilute solutions of chloride of lime (calcium hypochlorite) at doses of 0.2 to 0.35 ppm. The treatment process was conceived by Dr. John L. Leal and the chlorination plant was designed by George Warren Fuller.[47] Over the next few years, chlorine disinfection using chloride of lime were rapidly installed in drinking water systems around the world.[48]
In 1904, Allen Hazen showed that the efficiency of a sedimentation process was a function of the particle settling velocity, the flow through the tank and the surface area of tank. Sedimentation tanks are typically designed within a range of overflow rates of 0.5 to 1.0 gallons per minute per square foot (or 1.25 to 2.5 litres per square meter per hour). In general, sedimentation basin efficiency is not a function of detention time or depth of the basin. Although, basin depth must be sufficient so that water currents do not disturb the sludge and settled particle interactions are promoted. As particle concentrations in the settled water increase near the sludge surface on the bottom of the tank, settling velocities can increase due to collisions and agglomeration of particles. Typical detention times for sedimentation vary from 1.5 to 4 hours and basin depths vary from 10 to 15 feet (3 to 4.5 meters).[6]:9.39–9.40[7]:790–1[8]:140–2, 171
×