Photo by purolipanFor flexibility, a good multi-tool is a camper’s best friend, and there are hundreds of models on the market. When comparing the need for different functions and the tool’s weight, it becomes apparent that simpler is better. Look for a multi-tool that has a regular and serrated blade, pliers with a wire cutter, carbide knife sharpener, bottle and can opener, and a lanyard loop. Pay close attention to the materials and quality; look for titanium handles, 154CM steel blades, and 420 stainless steel construction. If you plan on carrying a small hatchet for cutting firewood, consider a multi-tool hatchet and take one tool instead of two.
Pure water has a pH close to 7 (neither alkaline nor acidic). Sea water can have pH values that range from 7.5 to 8.4 (moderately alkaline). Fresh water can have widely ranging pH values depending on the geology of the drainage basin or aquifer and the influence of contaminant inputs (acid rain). If the water is acidic (lower than 7), lime, soda ash, or sodium hydroxide can be added to raise the pH during water purification processes. Lime addition increases the calcium ion concentration, thus raising the water hardness. For highly acidic waters, forced draft degasifiers can be an effective way to raise the pH, by stripping dissolved carbon dioxide from the water. Making the water alkaline helps coagulation and flocculation processes work effectively and also helps to minimize the risk of lead being dissolved from lead pipes and from lead solder in pipe fittings. Sufficient alkalinity also reduces the corrosiveness of water to iron pipes. Acid (carbonic acid, hydrochloric acid or sulfuric acid) may be added to alkaline waters in some circumstances to lower the pH. Alkaline water (above pH 7.0) does not necessarily mean that lead or copper from the plumbing system will not be dissolved into the water. The ability of water to precipitate calcium carbonate to protect metal surfaces and reduce the likelihood of toxic metals being dissolved in water is a function of pH, mineral content, temperature, alkalinity and calcium concentration.
Reverse osmosis per its construction removes both harmful contaminants present in the water, as well as some desirable minerals. Modern studies on this matter have been quite shallow, citing lack of funding and interest in such study, as re-mineralization on the treatment plants today is done to prevent pipeline corrosion without going into human health aspect. They do, however link to older, more thorough studies that at one hand show some relation between long-term health effects and consumption of water low on calcium and magnesium, on the other confess that none of these older studies comply to modern standards of research 
Filter Speed While there are reverse osmosis filters that can filter water as you need it, most of them take some time to refill. If you are replacing your regular tap water with purified water, look for a unit that can filter 50 or more gallons a day. If you're just using it for drinking water, you can opt for a unit with a slower refill rate and a smaller tank.
Ion exchange: Ion exchange systems use ion exchange resin- or zeolite-packed columns to replace unwanted ions. The most common case is water softening consisting of removal of Ca2+ and Mg2+ ions replacing them with benign (soap friendly) Na+ or K+ ions. Ion exchange resins are also used to remove toxic ions such as nitrite, lead, mercury, arsenic and many others.
Treatment with reverse osmosis is limited, resulting in low recoveries on high concentration (measured with electrical conductivity) and fouling of the RO membranes. Reverse osmosis applicability is limited by conductivity, organics, and scaling inorganic elements such as CaSO4, Si, Fe and Ba. Low organic scaling can use two different technologies, one is using spiral wound membrane type of module, and for high organic scaling, high conductivity and higher pressure (up to 90 bars) disc tube modules with reverse-osmosis membranes can be used. Disc tube modules were redesigned for landfill leachate purification, that is usually contaminated with high levels of organic material. Due to the cross-flow with high velocity it is given a flow booster pump, that is recirculating the flow over the same membrane surface between 1.5 and 3 times before it is released as a concentrate. High velocity is also good against membrane scaling and allows successful membrane cleaning.
The pore size of the filter, usually measured in microns, will determine what will be filtered through. While a standard micron size of 0.2 is small enough to block heavy metals such as lead and copper and large parasites such as Cryptosporidium, it will not block viruses. The National Sanitation Foundation sets a standard for effective water filtration products so look for an NSF stamp when selecting a filter to purchase.
I love this new ro system, I've never installed one of these before but luckily the dvd walked me through it step by step. With the Ppm meter they gave me I tested my water for the first time before and after. My ppm went from 275 to 8. I’m very pleased so far. Easy to install and I'm loving it ! Thank you so much for providing a great quality product with a simple set up for great tasting water :)
Some water supplies may also contain disinfections by-products, inorganic chemicals, organic chemicals, and radionuclides. Specialized methods for controlling formation or removing them can also be part of water treatment. To learn more about the different treatments for drinking water, see the National Drinking Water Clearinghouse’s Fact Sheet Series on Drinking Water TreatmentsExternal.
Formally, reverse osmosis is the process of forcing a solvent from a region of high solute concentration through a semipermeable membrane to a region of low-solute concentration by applying a pressure in excess of the osmotic pressure. The largest and most important application of reverse osmosis is the separation of pure water from seawater and brackish waters; seawater or brackish water is pressurized against one surface of the membrane, causing transport of salt-depleted water across the membrane and emergence of potable drinking water from the low-pressure side.
The first part of the purification tag team must eliminate microorganisms, like harmful bacteria and parasites. There are a handful of tried and true methods for doing this. The most familiar is boiling. Simply bringing water up to its boiling point of 212 degrees Fahrenheit will kill almost all microorganisms, so just a few minutes of boiling will do the job.