Advantage is that you are not adding any chemicals to your water, which takes out the guess work as far as dosage. The disadvantage, if it can even be called that, is that you have to have a source of heat(fire, stove, etc.) in order to bring the water to the boiling point. Also we have to remember that this does not remove chemical such as petroleum or pesticides which can be harmful as well.
A nice feature of the Sawyer system is the benefit of using the same filter as a water treatment bottle, inline on a hydration pack, as an ultra light drink straw and attached to a faucet with the included faucet adaptor. If purchased with the faucet adaptor kit, it can be configured to drink straight from the tap during boil alerts or in areas of natural disasters such as floods, hurricanes, and earthquakes. The kit also provides hydration pack assembly kit for installing the inline filter on a hydration pack.
Fluoride Removal: Although fluoride is added to water in many areas, some areas of the world have excessive levels of natural fluoride in the source water. Excessive levels can be toxic or cause undesirable cosmetic effects such as staining of teeth. Methods of reducing fluoride levels is through treatment with activated alumina and bone char filter media.
Radium Removal: Some groundwater sources contain radium, a radioactive chemical element. Typical sources include many groundwater sources north of the Illinois River in Illinois, United States of America. Radium can be removed by ion exchange, or by water conditioning. The back flush or sludge that is produced is, however, a low-level radioactive waste.
As science and technology continue to improve, more efficient systems in purifying water are invented, established, and standardized. In the United States, laws are passed to ensure that businesses and corporations who manufacture and distribute water adhere to strict purification standards. Local municipalities are also held to strict standards in order to ensure that communities are given clean water consistently.
Boiling: Bringing water to its boiling point (about 100 °C or 212 F at sea level), is the oldest and most effective way since it eliminates most microbes causing intestine related diseases,[21] but it cannot remove chemical toxins or impurities.[22] For human health, complete sterilization of water is not required, since the heat resistant microbes are not intestine affecting.[21] The traditional advice of boiling water for ten minutes is mainly for additional safety, since microbes start getting eliminated at temperatures greater than 60 °C (140 °F). Though the boiling point decreases with increasing altitude, it is not enough to affect the disinfecting process.[21][23] In areas where the water is "hard" (that is, containing significant dissolved calcium salts), boiling decomposes the bicarbonate ions, resulting in partial precipitation as calcium carbonate. This is the "fur" that builds up on kettle elements, etc., in hard water areas. With the exception of calcium, boiling does not remove solutes of higher boiling point than water and in fact increases their concentration (due to some water being lost as vapour). Boiling does not leave a residual disinfectant in the water. Therefore, water that is boiled and then stored for any length of time may acquire new pathogens.
I have wanted an RO system for awhile and this seemed the best for a reasonable price. Great water filtration, very fast faucet flow, great water conservation for RO, and easy to install. After four hours today I have it installed and I tested my tap water, my brita pitcher, and then the RO water with a TDS meter (which measures the total dissolved solids in a liquid) and aquarium PH liquid tests (best thing I had on hand). Also I am 21 and havent done anything like this before but I think for what it is it was pretty easy to install. I will post my results from the tests below, they speak for themselves. My Brita Pitcher was BS and RO cant be beat. I will post another review if anything happens in the next year or so to make sure these results last.

The clarified water is then fed through a high-pressure piston pump into a series of vessels where it is subject to reverse osmosis. The product water is free of 90.00–99.98% of the raw water's total dissolved solids and by military standards, should have no more than 1000–1500 parts per million by measure of electrical conductivity. It is then disinfected with chlorine and stored for later use.[citation needed]
In 1977 Cape Coral, Florida became the first municipality in the United States to use the RO process on a large scale with an initial operating capacity of 11.35 million liters (3 million US gal) per day. By 1985, due to the rapid growth in population of Cape Coral, the city had the largest low-pressure reverse-osmosis plant in the world, capable of producing 56.8 million liters (15 million US gal) per day (MGD).[7]
STAT: The number of annual deaths from ESD in the U.S. are unknown, since they are counted among all drownings. But anecdotal evidence shows that ESD is widespread. ESD prevention groups have successfully urged some states to enact safety standards, including the installation of ground-fault circuit interrupters and a central shutoff for a dock's electrical system.
×