One of the most frequent compliments of the Home Master Full Contact Reverse Osmosis Water Filter System is that it delivers great water pressure when compared to other reverse osmosis kits. This can be credited to the permeate pump along with the 3/8 inch dispenser tubing used in this system, which results in a faster flow of water than the typical ¼ inch tubing found on many other reverse osmosis systems.
I love this new ro system, I've never installed one of these before but luckily the dvd walked me through it step by step. With the Ppm meter they gave me I tested my water for the first time before and after. My ppm went from 275 to 8. I’m very pleased so far. Easy to install and I'm loving it ! Thank you so much for providing a great quality product with a simple set up for great tasting water :)
The first experiments into water filtration were made in the 17th century. Sir Francis Bacon attempted to desalinate sea water by passing the flow through a sand filter. Although his experiment did not succeed, it marked the beginning of a new interest in the field. The fathers of microscopy, Antonie van Leeuwenhoek and Robert Hooke, used the newly invented microscope to observe for the first time small material particles that lay suspended in the water, laying the groundwork for the future understanding of waterborne pathogens.[36]
That brings us to filtration by manufactured filters. These devices allow us to go into microfiltration and ultrafiltration. By simply running the water through these porous ceramic filters we can effectively remove bacteria and viruses depending on the quality of the filter and the pore size. See chart above. This is where high quality filters such as the Katadyn Combi Filter can filter down to 0.2-micron level capturing Giardia, Crypto, bacteria and most viruses. Some filters are chemically impregnated to ensure complete removal of bacteria. The information below will give more detail.
The system came in a well packaged box and I found everything easily including some spare parts for future use, which I appreciate. Fittings and pipes were included. All I need was the tools (wrench, scissors, etc) and a Teflon sealer that I got from Home Depot. I noticed a little trace of water and I found out that iSpring did a real test for quality control so that's a good ... full review

The filters can be changed easily without the help of any tools. You don’t have to worry if you have forgotten about the schedule to change the filters. You will have stickers along the brondell that reminds you to change them. Even LED Light indicator will not let you forget about the maintenance time. LED Light on Faucet will glow whenever it is needed.
Ion exchange:[11] Ion exchange systems use ion exchange resin- or zeolite-packed columns to replace unwanted ions. The most common case is water softening consisting of removal of Ca2+ and Mg2+ ions replacing them with benign (soap friendly) Na+ or K+ ions. Ion exchange resins are also used to remove toxic ions such as nitrite, lead, mercury, arsenic and many others.

Reverse osmosis: Mechanical pressure is applied to an impure solution to force pure water through a semi-permeable membrane. Reverse osmosis is theoretically the most thorough method of large scale water purification available, although perfect semi-permeable membranes are difficult to create. Unless membranes are well-maintained, algae and other life forms can colonize the membranes.
Pretreatment is important when working with reverse osmosis and nanofiltration membranes due to the nature of their spiral-wound design. The material is engineered in such a fashion as to allow only one-way flow through the system. As such, the spiral-wound design does not allow for backpulsing with water or air agitation to scour its surface and remove solids. Since accumulated material cannot be removed from the membrane surface systems, they are highly susceptible to fouling (loss of production capacity). Therefore, pretreatment is a necessity for any reverse osmosis or nanofiltration system. Pretreatment in sea water reverse osmosis systems has four major components:

The addition of inorganic coagulants such as aluminum sulfate (or alum) or iron (III) salts such as iron(III) chloride cause several simultaneous chemical and physical interactions on and among the particles. Within seconds, negative charges on the particles are neutralized by inorganic coagulants. Also within seconds, metal hydroxide precipitates of the iron and aluminium ions begin to form. These precipitates combine into larger particles under natural processes such as Brownian motion and through induced mixing which is sometimes referred to as flocculation. Amorphous metal hydroxides are known as "floc". Large, amorphous aluminum and iron (III) hydroxides adsorb and enmesh particles in suspension and facilitate the removal of particles by subsequent processes of sedimentation and filtration.[6]:8.2–8.3