Whether I've owned or rented. Country cottage, or city condo. The last one was a 2 stage G.E. undersink model which lasted about 9 years, until the filters started to get bad manufacture reviews. It's hard to find filter systems that are super quality, pro size, like the APEC WFS-1000 without going reverse osmosis. This system is the same size as a whole house filter, but made for undersink drinking water!
The EPA states that there are four main types of contaminants to be found in water. The Safe Drinking Water Act (SDWA), a federal law that protects public drinking water supplies, defines "contaminant" as anything other than water molecules. We can reasonably expect most drinking water to contain some level of contaminant, especially since minerals such as calcium and magnesium fall into that category. The question is, which of these contaminants are harmful and how much of it is entering my system?
In 1977 Cape Coral, Florida became the first municipality in the United States to use the RO process on a large scale with an initial operating capacity of 11.35 million liters (3 million US gal) per day. By 1985, due to the rapid growth in population of Cape Coral, the city had the largest low-pressure reverse-osmosis plant in the world, capable of producing 56.8 million liters (15 million US gal) per day (MGD).[7]
A nice feature of the Sawyer system is the benefit of using the same filter as a water treatment bottle, inline on a hydration pack, as an ultra light drink straw and attached to a faucet with the included faucet adaptor. If purchased with the faucet adaptor kit, it can be configured to drink straight from the tap during boil alerts or in areas of natural disasters such as floods, hurricanes, and earthquakes. The kit also provides hydration pack assembly kit for installing the inline filter on a hydration pack.
Boiling: Bringing water to its boiling point (about 100 °C or 212 F at sea level), is the oldest and most effective way since it eliminates most microbes causing intestine related diseases,[21] but it cannot remove chemical toxins or impurities.[22] For human health, complete sterilization of water is not required, since the heat resistant microbes are not intestine affecting.[21] The traditional advice of boiling water for ten minutes is mainly for additional safety, since microbes start getting eliminated at temperatures greater than 60 °C (140 °F). Though the boiling point decreases with increasing altitude, it is not enough to affect the disinfecting process.[21][23] In areas where the water is "hard" (that is, containing significant dissolved calcium salts), boiling decomposes the bicarbonate ions, resulting in partial precipitation as calcium carbonate. This is the "fur" that builds up on kettle elements, etc., in hard water areas. With the exception of calcium, boiling does not remove solutes of higher boiling point than water and in fact increases their concentration (due to some water being lost as vapour). Boiling does not leave a residual disinfectant in the water. Therefore, water that is boiled and then stored for any length of time may acquire new pathogens.
The water from this unit is pretty much tasteless to me, which is ideal since tap water tastes awful. I grew up with Culligan, which has a certain taste to me, versus this which is just pure. Haven't tested it but plan to. We also added a line to the fridge ice maker so our ice is purified. It was easy to install in our home, and we've used it three months with no issues. The cables are long. today when our sink clogged and we had to drain it, got a mess over all the filters, and they water tubes were all long enough to put the whole unit (still assembled and attached), into the sink to rinse it off. I'm glad it's made in the USA so I know all the parts have stringent manufacturing guidelines. The only thing I would change, is ordering directly from apec instead ... full review
What many poor people, backcountry hikers, and those living in remote areas have in common are a reliance on untreated, local sources of water that may be contaminated, and must be purified before it can be safely consumed. There are two basic approaches to water purification: using a reverse osmosis filter, or a tag team of two methods working together to eliminate two separate contaminants.
I have wanted an RO system for awhile and this seemed the best for a reasonable price. Great water filtration, very fast faucet flow, great water conservation for RO, and easy to install. After four hours today I have it installed and I tested my tap water, my brita pitcher, and then the RO water with a TDS meter (which measures the total dissolved solids in a liquid) and aquarium PH liquid tests (best thing I had on hand). Also I am 21 and havent done anything like this before but I think for what it is it was pretty easy to install. I will post my results from the tests below, they speak for themselves. My Brita Pitcher was BS and RO cant be beat. I will post another review if anything happens in the next year or so to make sure these results last.
A properly packed backpack is requisite to your comfort and safety. Incorrect weight distribution leads to muscle aches and unnecessary strain on your spine. Place heavy items – water, food, and cooking gear – in the middle of your pack, close to your body. Use medium weight items – clothing, tarps, and rain gear – to cushion the heavier items, securing them, so the weight does not shift while you are hiking. Pack your sleeping bag in the bottom of your backpack or tie to the bottom. Store items that you are likely to need more frequently in the side and outer pockets – compass and map, sunglasses, toilet tissue and trowel, sunscreen, bug repellent, pocketknife, flashlight, snacks, and a small towel.
I've just finished installation of your 5 stage home drinking reverse osmosis system and I have a few suggestions for improvement. It looks like the faucet included in the package is different than the one in the instructions. I like the upgrade, but it would be nice if you included a compatible quick connect adapter. The Quick Connect adapter that was included (pictured on the right) has threading that is too large to fit on the faucet. The packing nut attachment doesn't work well with plastic tubing.

In 1904, Allen Hazen showed that the efficiency of a sedimentation process was a function of the particle settling velocity, the flow through the tank and the surface area of tank. Sedimentation tanks are typically designed within a range of overflow rates of 0.5 to 1.0 gallons per minute per square foot (or 1.25 to 2.5 litres per square meter per hour). In general, sedimentation basin efficiency is not a function of detention time or depth of the basin. Although, basin depth must be sufficient so that water currents do not disturb the sludge and settled particle interactions are promoted. As particle concentrations in the settled water increase near the sludge surface on the bottom of the tank, settling velocities can increase due to collisions and agglomeration of particles. Typical detention times for sedimentation vary from 1.5 to 4 hours and basin depths vary from 10 to 15 feet (3 to 4.5 meters).[6]:9.39–9.40[7]:790–1[8]:140–2, 171
×