Advantage is that you are not adding any chemicals to your water, which takes out the guess work as far as dosage. The disadvantage, if it can even be called that, is that you have to have a source of heat(fire, stove, etc.) in order to bring the water to the boiling point. Also we have to remember that this does not remove chemical such as petroleum or pesticides which can be harmful as well.
Iodine solutions kill bacteria by upsetting the ion balance within the cell, replacing chemicals that the bacteria needs to survive with iodide ions. Iodine can also be poisonous to humans, and can be especially harmful to young children, and pregnant women. You should be careful not to use too much iodine when purifying your water, and if at all possible avoid using it as a primary purification method for extended periods of time. If you find yourself in a survival situation, for an extended period of time, you should consider setting up a still, or boiling the water if possible.

Purifying water can be done through a variety of methods, like using a filter, treating with chemicals, or boiling. Water should be purified whenever you have reason to believe that it could be contaminated. Typically, this is necessary if you are camping in the wilderness or your home water source has been compromised. Whatever the reason, purifying water will remove any sediments and contaminants, as well as kill any germs, so that you can enjoy clean water without worrying about getting sick.
The most common type of filter is a rapid sand filter. Water moves vertically through sand which often has a layer of activated carbon or anthracite coal above the sand. The top layer removes organic compounds, which contribute to taste and odour. The space between sand particles is larger than the smallest suspended particles, so simple filtration is not enough. Most particles pass through surface layers but are trapped in pore spaces or adhere to sand particles. Effective filtration extends into the depth of the filter. This property of the filter is key to its operation: if the top layer of sand were to block all the particles, the filter would quickly clog.[9]
The clarified water is then fed through a high-pressure piston pump into a series of vessels where it is subject to reverse osmosis. The product water is free of 90.00–99.98% of the raw water's total dissolved solids and by military standards, should have no more than 1000–1500 parts per million by measure of electrical conductivity. It is then disinfected with chlorine and stored for later use.[citation needed]
Ultraviolet light (UV) is very effective at inactivating cysts, in low turbidity water. UV light's disinfection effectiveness decreases as turbidity increases, a result of the absorption, scattering, and shadowing caused by the suspended solids. The main disadvantage to the use of UV radiation is that, like ozone treatment, it leaves no residual disinfectant in the water; therefore, it is sometimes necessary to add a residual disinfectant after the primary disinfection process. This is often done through the addition of chloramines, discussed above as a primary disinfectant. When used in this manner, chloramines provide an effective residual disinfectant with very few of the negative effects of chlorination.

We were looking for to replace an RO unit that was many years old and were impressed with iSpring's RO / UV / Ph / multi-filter options, with the More-Is-Better paradigm. Patience is required for the multipart installation because the directions are vague. We also had to run a GFCI receptacle for the UV. The UV does warm the water a bit but we remedied this by running an additional line to the fridge for cold water and ice. The system was flushed a half dozen time over two days. The initial glass was cloudy but that cleared to show some carbon from that particular filter. The water taste great and we highly recommend this drinking water system.
The booster pump included with this tankless reverse osmosis system requires electricity but helps to maximize the efficiency of the system. It can achieve up to a 1:1 ratio of purified to wastewater. However, in real-world use, some people found that wastewater was more like 2 gallons for every 1 gallon of purified water produced. iSprings points out that many factors affect this efficiency rating, so some variance in results is to be expected.

A reverse osmosis water purification unit (ROWPU) is a portable, self-contained water treatment plant. Designed for military use, it can provide potable water from nearly any water source. There are many models in use by the United States armed forces and the Canadian Forces. Some models are containerized, some are trailers, and some are vehicles unto themselves.[citation needed]


Sip on pure, clean water with the addition of the APEC Ultimate 6-Stage Reverse Osmosis Water Filter System for home. This reverse osmosis system is easy to mount under the sink and earns top marks for easy installation and excellent customer service. With super capacity filters, you only need to change the filters once a year to enjoy clean and safe water every day.
I love this new ro system, I've never installed one of these before but luckily the dvd walked me through it step by step. With the Ppm meter they gave me I tested my water for the first time before and after. My ppm went from 275 to 8. I’m very pleased so far. Easy to install and I'm loving it ! Thank you so much for providing a great quality product with a simple set up for great tasting water :)
The first experiments into water filtration were made in the 17th century. Sir Francis Bacon attempted to desalinate sea water by passing the flow through a sand filter. Although his experiment did not succeed, it marked the beginning of a new interest in the field. The fathers of microscopy, Antonie van Leeuwenhoek and Robert Hooke, used the newly invented microscope to observe for the first time small material particles that lay suspended in the water, laying the groundwork for the future understanding of waterborne pathogens.[36]
The pore size of the filter, usually measured in microns, will determine what will be filtered through. While a standard micron size of 0.2 is small enough to block heavy metals such as lead and copper and large parasites such as Cryptosporidium, it will not block viruses. The National Sanitation Foundation sets a standard for effective water filtration products so look for an NSF stamp when selecting a filter to purchase.
Reverse osmosis differs from filtration in that the mechanism of fluid flow is by osmosis across a membrane. The predominant removal mechanism in membrane filtration is straining, or size exclusion, where the pores are 0.01 micrometers or larger, so the process can theoretically achieve perfect efficiency regardless of parameters such as the solution's pressure and concentration. Reverse osmosis instead involves solvent diffusion across a membrane that is either nonporous or uses nanofiltration with pores 0.001 micrometers in size. The predominant removal mechanism is from differences in solubility or diffusivity, and the process is dependent on pressure, solute concentration, and other conditions.[2] Reverse osmosis is most commonly known for its use in drinking water purification from seawater, removing the salt and other effluent materials from the water molecules.[3]
A properly packed backpack is requisite to your comfort and safety. Incorrect weight distribution leads to muscle aches and unnecessary strain on your spine. Place heavy items – water, food, and cooking gear – in the middle of your pack, close to your body. Use medium weight items – clothing, tarps, and rain gear – to cushion the heavier items, securing them, so the weight does not shift while you are hiking. Pack your sleeping bag in the bottom of your backpack or tie to the bottom. Store items that you are likely to need more frequently in the side and outer pockets – compass and map, sunglasses, toilet tissue and trowel, sunscreen, bug repellent, pocketknife, flashlight, snacks, and a small towel.
Direct contact membrane distillation (DCMD). Applicable to desalination. Heated seawater is passed along the surface of a hydrophobic polymer membrane. Evaporated water passes from the hot side through pores in the membrane into a stream of cold pure water on the other side. The difference in vapour pressure between the hot and cold side helps to push water molecules through.
Use a commercial water filter. A commercial water filter is the easiest and most effective way to filter sediment, pathogens, metals, and other pollutants from water. These filters contain special materials like charcoal, carbon, ceramic, sand, and cloth that are specially designed to filter out dangerous pollutants.[7] There are many different types of filters you can use, including:

These tablets essentially use chlorination as their method of purification. Sodium chlorite generate chlorine dioxide giving it the ability to treat water. Chlorination, as most know, is a common method of disinfecting water, and is commonly used by municipalities world-wide for this purpose. Chlorine destroys bacteria by destroying the cell walls of the bacterium/virus, killing the organism. Fortunately, when we drink chlorinated water, our digestive system quickly neutralizes the chlorine. So chlorine concentrations along the gastrointestinal tract are, in all likelihood, too low to cause damage. The tablets are wrapped in a metallic foil which makes it easy to store and there are no concerns of a glass bottle breaking. This is one of our favorite items to carry as a backup to our water filtration system.
Treatment with reverse osmosis is limited, resulting in low recoveries on high concentration (measured with electrical conductivity) and fouling of the RO membranes. Reverse osmosis applicability is limited by conductivity, organics, and scaling inorganic elements such as CaSO4, Si, Fe and Ba. Low organic scaling can use two different technologies, one is using spiral wound membrane type of module, and for high organic scaling, high conductivity and higher pressure (up to 90 bars) disc tube modules with reverse-osmosis membranes can be used. Disc tube modules were redesigned for landfill leachate purification, that is usually contaminated with high levels of organic material. Due to the cross-flow with high velocity it is given a flow booster pump, that is recirculating the flow over the same membrane surface between 1.5 and 3 times before it is released as a concentrate. High velocity is also good against membrane scaling and allows successful membrane cleaning.
Treatment with reverse osmosis is limited, resulting in low recoveries on high concentration (measured with electrical conductivity) and fouling of the RO membranes. Reverse osmosis applicability is limited by conductivity, organics, and scaling inorganic elements such as CaSO4, Si, Fe and Ba. Low organic scaling can use two different technologies, one is using spiral wound membrane type of module, and for high organic scaling, high conductivity and higher pressure (up to 90 bars) disc tube modules with reverse-osmosis membranes can be used. Disc tube modules were redesigned for landfill leachate purification, that is usually contaminated with high levels of organic material. Due to the cross-flow with high velocity it is given a flow booster pump, that is recirculating the flow over the same membrane surface between 1.5 and 3 times before it is released as a concentrate. High velocity is also good against membrane scaling and allows successful membrane cleaning.
Photo by purolipanFor flexibility, a good multi-tool is a camper’s best friend, and there are hundreds of models on the market. When comparing the need for different functions and the tool’s weight, it becomes apparent that simpler is better. Look for a multi-tool that has a regular and serrated blade, pliers with a wire cutter, carbide knife sharpener, bottle and can opener, and a lanyard loop. Pay close attention to the materials and quality; look for titanium handles, 154CM steel blades, and 420 stainless steel construction. If you plan on carrying a small hatchet for cutting firewood, consider a multi-tool hatchet and take one tool instead of two.

Only a part of the saline feed water pumped into the membrane assembly passes through the membrane with the salt removed. The remaining "concentrate" flow passes along the saline side of the membrane to flush away the concentrated salt solution. The percentage of desalinated water produced versus the saline water feed flow is known as the "recovery ratio". This varies with the salinity of the feed water and the system design parameters: typically 20% for small seawater systems, 40% – 50% for larger seawater systems, and 80% – 85% for brackish water. The concentrate flow is at typically only 3 bar / 50 psi less than the feed pressure, and thus still carries much of the high-pressure pump input energy.
Ultraviolet light (UV) is very effective at inactivating cysts, in low turbidity water. UV light's disinfection effectiveness decreases as turbidity increases, a result of the absorption, scattering, and shadowing caused by the suspended solids. The main disadvantage to the use of UV radiation is that, like ozone treatment, it leaves no residual disinfectant in the water; therefore, it is sometimes necessary to add a residual disinfectant after the primary disinfection process. This is often done through the addition of chloramines, discussed above as a primary disinfectant. When used in this manner, chloramines provide an effective residual disinfectant with very few of the negative effects of chlorination.
There are five types of contaminants that are found in water: particulates, bacteria, minerals, chemicals, and pharmaceuticals. Methods to remove these elements range from simple and inexpensive to elaborate and costly. Often to achieve purely potable water, several technologies must be combined in a particular sequence. Listed here are general brief descriptions of the twenty-five methods to purify water.
The other half of the tag team is to eliminate pollutants. The best way to do this is with a homemade carbon filter. This uses the same technology as Brita filters. Carbon is a chemically active substance, with a tendency to bind to most anything. At a microscopic level, charcoal is a heavily pitted and striated material, which vastly increases its real surface area. The result is that when water slowly runs over charcoal, pollutants find themselves glued to the charcoal surface. An improvised filter can be made out of ground-up charcoal, a strainer and a funnel. Bear Gryllis made a purification drinking straw out of little more than a reed and some charcoal bits for the Discovery Channel's "Man vs. Wild." It's a simple technique, but it is highly effective.
Remove heavy metals with cilantro. Just as pine trees are effective at removing pathogens, so too is cilantro excellent at removing heavy metals from water. Fill a pitcher with water and place a handful of cilantro leaves into the pitcher. Stir the water and let the leaves sit in the water for at least an hour. Remove and discard the cilantro before drinking the water.[11]
Photo by purolipanFor flexibility, a good multi-tool is a camper’s best friend, and there are hundreds of models on the market. When comparing the need for different functions and the tool’s weight, it becomes apparent that simpler is better. Look for a multi-tool that has a regular and serrated blade, pliers with a wire cutter, carbide knife sharpener, bottle and can opener, and a lanyard loop. Pay close attention to the materials and quality; look for titanium handles, 154CM steel blades, and 420 stainless steel construction. If you plan on carrying a small hatchet for cutting firewood, consider a multi-tool hatchet and take one tool instead of two.
A nice feature of the Sawyer system is the benefit of using the same filter as a water treatment bottle, inline on a hydration pack, as an ultra light drink straw and attached to a faucet with the included faucet adaptor. If purchased with the faucet adaptor kit, it can be configured to drink straight from the tap during boil alerts or in areas of natural disasters such as floods, hurricanes, and earthquakes. The kit also provides hydration pack assembly kit for installing the inline filter on a hydration pack.

These survival tips can help you avoid becoming just another statistic. Accidents are the leading cause of death among U.S. men 18 to 50 years old, accounting for 37,000 of the roughly 148,000 annual fatalities. Some instances of unintentional death, to use the official term, are unavoidable—wrong place, wrong time—but most aren't. Staying alive requires recognizing danger, feeling fear, and reacting. "We interpret external cues through our subconscious fear centers very quickly," says Harvard University's David Ropeik, author of How Risky Is It, Really? Trouble is, even smart, sober, experienced men can fail to register signals of an imminent threat. Here we present 20 easy-to-miss risks, and how to avoid or survive them.
"The overall study results revealed that the CHLOR-FLOC system was not adequate to physically remove, or to provide adequate chemical disinfection of, Cryptosporidium oocysts to the required level of 99.9 percent reduction. Water, Purification, CHLOR-FLOC tablets, Micro-organisms, Cryptosporidium, Klebseilla, Echovirus, Latex beads, Protozoan cysts, Bacteria, Disinfection, Coagulation." Source: oai.dtic.mil
Distillation removes all minerals from water, and the membrane methods of reverse osmosis and nanofiltration remove most to all minerals. This results in demineralized water which is not considered ideal drinking water. The World Health Organization has investigated the health effects of demineralized water since 1980.[32] Experiments in humans found that demineralized water increased diuresis and the elimination of electrolytes, with decreased blood serum potassium concentration. Magnesium, calcium, and other minerals in water can help to protect against nutritional deficiency. Demineralized water may also increase the risk from toxic metals because it more readily leaches materials from piping like lead and cadmium, which is prevented by dissolved minerals such as calcium and magnesium. Low-mineral water has been implicated in specific cases of lead poisoning in infants, when lead from pipes leached at especially high rates into the water. Recommendations for magnesium have been put at a minimum of 10 mg/L with 20–30 mg/L optimum; for calcium a 20 mg/L minimum and a 40–80 mg/L optimum, and a total water hardness (adding magnesium and calcium) of 2 to 4 mmol/L. At water hardness above 5 mmol/L, higher incidence of gallstones, kidney stones, urinary stones, arthrosis, and arthropathies have been observed.[33] Additionally, desalination processes can increase the risk of bacterial contamination.[33]

Whether you are on a backpacking trip or find yourself in an unplanned emergency situation our first goal is to locate water. Depending on the location this may prove more difficult than ensuring it's potability. Make sure you are familiar with water sources in the area you plan to travel. Looking at topographical maps is always a good idea. Depending on the dates of the map this could help you find water while backpacking. As with other areas of emergency preparedness, make sure to have a backup plan. Water sources can change with time and seasonal changes. Another important aspect of finding water is the lay of the land. Learning the elevational changes of the area and thinking which way the water would travel during a rain can be another way to locate a water source. For the scope of this article, we will assume that a source has been located.
The reverse osmosis membrane used in the RCC7AK is rated for up to 75 gallons per day, which is plenty to meet the needs of most households shopping for an under sink reverse osmosis system. It takes anywhere from 1 to 3 hours to fill the storage tank, but once the tank is full, you’ll have purified water ready and waiting under the sink. A lead-free brushed nickel metal faucet for countertop installation is included so you can bypass the tap and have fresh, clean water on demand.
Filter Speed While there are reverse osmosis filters that can filter water as you need it, most of them take some time to refill. If you are replacing your regular tap water with purified water, look for a unit that can filter 50 or more gallons a day. If you're just using it for drinking water, you can opt for a unit with a slower refill rate and a smaller tank.
Reverse osmosis is extensively used in the dairy industry for the production of whey protein powders and for the concentration of milk to reduce shipping costs. In whey applications, the whey (liquid remaining after cheese manufacture) is concentrated with reverse osmosis from 6% total solids to 10–20% total solids before ultrafiltration processing. The ultrafiltration retentate can then be used to make various whey powders, including whey protein isolate. Additionally, the ultrafiltration permeate, which contains lactose, is concentrated by reverse osmosis from 5% total solids to 18–22% total solids to reduce crystallization and drying costs of the lactose powder.
Sea-water reverse-osmosis (SWRO) desalination, a membrane process, has been commercially used since the early 1970s. Its first practical use was demonstrated by Sidney Loeb from University of California at Los Angeles in Coalinga, California, and Srinivasa Sourirajan of National Research Council, Canada. Because no heating or phase changes are needed, energy requirements are low, around 3 kWh/m3, in comparison to other processes of desalination, but are still much higher than those required for other forms of water supply, including reverse osmosis treatment of wastewater, at 0.1 to 1 kWh/m3. Up to 50% of the seawater input can be recovered as fresh water, though lower recoveries may reduce membrane fouling and energy consumption.
In a paper published in 1894, Moritz Traube formally proposed the addition of chloride of lime (calcium hypochlorite) to water to render it "germ-free." Two other investigators confirmed Traube's findings and published their papers in 1895.[42] Early attempts at implementing water chlorination at a water treatment plant were made in 1893 in Hamburg, Germany and in 1897 the city of Maidstone, England was the first to have its entire water supply treated with chlorine.[43]

Furthermore, animals have to drink and are known to visit water holes. This raises several concerns, 1) Animals are not very mindful of their toilet etiquette and 2) Predators will sometimes use water holes as a place of attack. If we were desperate, (dying of thirst) and had no way to purify the water, first we really should ask ourselves how we got ourselves into such a situation, then we would have no choice but to drink the water in hopes that we are rescued before the water borne disease kills us. Think outside the box, is there a way to get a makeshift bowl (wood, vegetation) and use hot rocks to boil the water. Is there any material around, bamboo etc that can be used to slowly bring the water to a boil. Build a multiple stage filter using sand, charcoal and sphagnum moss which has been known to contain some levels of iodine. If all that fails then we would be faced with the choice of drinking the untreated water. We know that moving water is preferable to standing water, but what can we do. We can walk around the water source, find the area with the least animal traffic and preferably a sandy shoreline. We can then dig a hole near the water deep enough to allow water to collect. The distance from the water source will have to be judged by the soil we are digging. The hope here is that the water will slowly seep into the hole and begin to collect while being "filtered" by the sand and rocks. At this point we have to get creative to get the water out. Perhaps make a straw out of natural materials or simply soak a bandana and squeeze it into our mouth. This would be a last resort and very risky.
The system came in a well packaged box and I found everything easily including some spare parts for future use, which I appreciate. Fittings and pipes were included. All I need was the tools (wrench, scissors, etc) and a Teflon sealer that I got from Home Depot. I noticed a little trace of water and I found out that iSpring did a real test for quality control so that's a good ... full review
Remove heavy metals with cilantro. Just as pine trees are effective at removing pathogens, so too is cilantro excellent at removing heavy metals from water. Fill a pitcher with water and place a handful of cilantro leaves into the pitcher. Stir the water and let the leaves sit in the water for at least an hour. Remove and discard the cilantro before drinking the water.[11]
Ion exchange:[11] Ion exchange systems use ion exchange resin- or zeolite-packed columns to replace unwanted ions. The most common case is water softening consisting of removal of Ca2+ and Mg2+ ions replacing them with benign (soap friendly) Na+ or K+ ions. Ion exchange resins are also used to remove toxic ions such as nitrite, lead, mercury, arsenic and many others.
Drinking water sources are subject to contamination and require appropriate treatment to remove disease-causing agents. Public drinking water systems use various methods of water treatment to provide safe drinking water for their communities. Today, the most common steps in water treatment used by community water systems (mainly surface water treatment) include:

In the production of bottled mineral water, the water passes through a reverse osmosis water processor to remove pollutants and microorganisms. In European countries, though, such processing of natural mineral water (as defined by a European directive[10]) is not allowed under European law. In practice, a fraction of the living bacteria can and do pass through reverse osmosis membranes through minor imperfections, or bypass the membrane entirely through tiny leaks in surrounding seals. Thus, complete reverse osmosis systems may include additional water treatment stages that use ultraviolet light or ozone to prevent microbiological contamination.


Assuming you can get a fire going, and have a metal container. After filtering as many of the particulates as possible. Fill your container with water, place over the fire, bring to a rapid boil, then allow to cool (drinking hot water can induce vomiting). Boiling will kill the harmful bacteria in the water, as they cannot withstand the temperature.

The most common type of filter is a rapid sand filter. Water moves vertically through sand which often has a layer of activated carbon or anthracite coal above the sand. The top layer removes organic compounds, which contribute to taste and odour. The space between sand particles is larger than the smallest suspended particles, so simple filtration is not enough. Most particles pass through surface layers but are trapped in pore spaces or adhere to sand particles. Effective filtration extends into the depth of the filter. This property of the filter is key to its operation: if the top layer of sand were to block all the particles, the filter would quickly clog.[9]


Water, apart from shelter, can become the most immediate need in a survival situation. Drinkable water is a vital resource. Depending on the level of activity, and ambient temperature, a person can live about 3 days without water. Prolonged activity without proper hydration coupled with malnutrition will quickly lower chances for survival. Finding a way to create and maintain a source of clean drinking water is essential for both short and long term emergency preparedness. Whether you find yourself lost in the wilderness or in an urban emergency scenario such as Katrina and Toledo's water crisis, water is life. Just one day without this precious fluid and we begin to see the symptoms of dehydration.
After installation, you have to fill and empty the tank to make it active. Normally you have filled and empty for 3-4 times but it depends on the system. You can check out how much water wastage is required from your instructional manual. This step in crucial. You will not have the safer, cleaner healthier purified water until you complete the last step.
All forms of chlorine are widely used, despite their respective drawbacks. One drawback is that chlorine from any source reacts with natural organic compounds in the water to form potentially harmful chemical by-products. These by-products, trihalomethanes (THMs) and haloacetic acids (HAAs), are both carcinogenic in large quantities and are regulated by the United States Environmental Protection Agency (EPA) and the Drinking Water Inspectorate in the UK. The formation of THMs and haloacetic acids may be minimized by effective removal of as many organics from the water as possible prior to chlorine addition. Although chlorine is effective in killing bacteria, it has limited effectiveness against pathogenic protozoa that form cysts in water such as Giardia lamblia and Cryptosporidium.
If you want to take a long swim underwater, the trick is to breathe in and out a few times and take a big gulp of air before you submerge. Right? Dead wrong. Hyperventilating not only doesn't increase the oxygen in your blood, it also decreases the amount of CO2, the compound that informs the brain of the need to breathe. Without that natural signal, you may hold your breath until you pass out and drown. This is known as shallow-water blackout.
Pretreatment is important when working with reverse osmosis and nanofiltration membranes due to the nature of their spiral-wound design. The material is engineered in such a fashion as to allow only one-way flow through the system. As such, the spiral-wound design does not allow for backpulsing with water or air agitation to scour its surface and remove solids. Since accumulated material cannot be removed from the membrane surface systems, they are highly susceptible to fouling (loss of production capacity). Therefore, pretreatment is a necessity for any reverse osmosis or nanofiltration system. Pretreatment in sea water reverse osmosis systems has four major components:

Ion exchange:[11] Ion exchange systems use ion exchange resin- or zeolite-packed columns to replace unwanted ions. The most common case is water softening consisting of removal of Ca2+ and Mg2+ ions replacing them with benign (soap friendly) Na+ or K+ ions. Ion exchange resins are also used to remove toxic ions such as nitrite, lead, mercury, arsenic and many others.
Water filtration is probably the most common method of purification for personal consumption, mainly because of its versatility and ease of use. Water filtration systems come in many forms and sizes, some of which are even portable. The most common water filtration systems are integrated with household sinks and refrigerators by connecting to the waterline.
Hikers on a glacier or in areas where patches of snow remain above the tree line may be tempted to speed downhill by sliding, or glissading. Bad idea: A gentle glide can easily lead to an unstoppable plummet. In 2005 climber Patrick Wang, 27, died on California's Mount Whitney while glissading off the summit; he slid 300 feet before falling off a 1000-foot cliff.
A reverse osmosis system is typically installed under the sink, but you can install it where your water enters the house, so all your water is filtered for contaminants. RO filter cartridges provide the most effective filtration of any water purifiers. The membrane and filters remove up to 99 percent of contaminants such as arsenic, lead, ammonia and chlorine, as well as toxic fluoride, sodium, nitrates and heavy metals. The 6 stage RO filters provide a deep filtering process, leaving you reverse osmosis water, free of sediments and toxins. RO water is perfect for drinking, cooking and making ice.
×